Forums
Sign In
Create Account
0
Today i received the set shown in the title.
Its my first Liteon 93450C and i've got a problem.
OK:
The Cuts (2-Way method) are made. And all cuts tested with multimeter. Everything is okay.
I connect the Xtractor with the drive (Xtractor is turned OFF) and connect the Xtractor to the Vampire (red wirde to PIN 5 on Xtractor and Vampire).
Then i start jungle flasher, choose my SATA Port and send the Intro.
I confirm the message from JF, and turn on my Xtractor with the Vampire on 101 and V3.3 on the board of my LiteOn.
Then the drive should turn into status 0x72. But nothin happens.
Xtractor LED is blue, Vampire LED is green. The vampire doesn't flash the blue LED and the status in JF ist still 0x7F.
Something is wrong. But i can't find the problem...
4 replies to this topic
Back to top
#2
Posted 18 November 2010 - 01:29 AM
-
- Moderators
-
- 776 posts
Super Moderator
NewBreeD, on 17 November 2010 - 07:30 PM, said:
Today i received the set shown in the title.
Its my first Liteon 93450C and i've got a problem.
OK:
The Cuts (2-Way method) are made. And all cuts tested with multimeter. Everything is okay.
I connect the Xtractor with the drive (Xtractor is turned OFF) and connect the Xtractor to the Vampire (red wirde to PIN 5 on Xtractor and Vampire).
Then i start jungle flasher, choose my SATA Port and send the Intro.
I confirm the message from JF, and turn on my Xtractor with the Vampire on 101 and V3.3 on the board of my LiteOn.
Then the drive should turn into status 0x72. But nothin happens.
Xtractor LED is blue, Vampire LED is green. The vampire doesn't flash the blue LED and the status in JF ist still 0x7F.
Something is wrong. But i can't find the problem...
Its my first Liteon 93450C and i've got a problem.
OK:
The Cuts (2-Way method) are made. And all cuts tested with multimeter. Everything is okay.
I connect the Xtractor with the drive (Xtractor is turned OFF) and connect the Xtractor to the Vampire (red wirde to PIN 5 on Xtractor and Vampire).
Then i start jungle flasher, choose my SATA Port and send the Intro.
I confirm the message from JF, and turn on my Xtractor with the Vampire on 101 and V3.3 on the board of my LiteOn.
Then the drive should turn into status 0x72. But nothin happens.
Xtractor LED is blue, Vampire LED is green. The vampire doesn't flash the blue LED and the status in JF ist still 0x7F.
Something is wrong. But i can't find the problem...
are you holding in the button as per directions when you power on the drive?
#3
Posted 18 November 2010 - 02:41 AM
-
- Members
-
- 3 posts
Newbie
Hello,
yes... i'm holding the vendor button on Vampire through the whole procedure.
But i dont get the blue LED on Vampire and JF is still sending the intro and is waiting for a drive.
yes... i'm holding the vendor button on Vampire through the whole procedure.
But i dont get the blue LED on Vampire and JF is still sending the intro and is waiting for a drive.
#4
Posted 18 November 2010 - 08:58 PM
-
- Moderators
-
- 776 posts
Super Moderator
you get blue light holding button, green light releasing button, which means you install in not proper or your cuts are not correct
#5
Posted 19 November 2010 - 08:56 AM
-
- Members
-
- 3 posts
Newbie
I guess my Vampire is defect.
Because my cutted points are really in a open Line. No connections to GND, etc.
I'll try it without vampire. My ordered Resistors will arrive me today.
Because my cutted points are really in a open Line. No connections to GND, etc.
I'll try it without vampire. My ordered Resistors will arrive me today.
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
Community Forum Software by IP.Board
Licensed to: Consoleaddiction.com